RE: ZOMGAH!!!!!!!
Login  | |
|
RE: ZOMGAH!!!!!!! - 5/13/2006 11:15:27 PM
|
|
|
PEPPERHEAD
Posts: 146
Joined: 8/17/2005
Status: offline
|
Don't see why it wouldn't work. If they will be seen maybe put some black cloth over them.
TASTE THE HEAT AND ENJOY THE PAIN
|
|
|
|
|
|
|
RE: ZOMGAH!!!!!!! - 5/13/2006 11:35:23 PM
|
|
|
Frenchy
Third Gen Dakota King
Posts: 5344
Joined: 12/11/2003
From: United States
Status: offline
|
Well, what is the purpose of them? I mean, if I built my box around it, but didnt have any way for air to get in, would that be fine? Like I would still have the 2 - 2.5 ft^3 around the vents, would that be fine? Or do I need to have the vents vent into the cabin?
_____________________________
Click me if you want me at the Dodge Forum Meet and Greet
|
|
|
|
|
RE: ZOMGAH!!!!!!! - 5/31/2006 6:24:31 PM
|
|
|
jimboscomp
DF Lighting Specialist
Posts: 912
Joined: 11/20/2005
From: Woodland Hills, CA
Status: offline
|
lookin good, try taking a look on my cardomain at Divyne's dakota clubcab, and his amp/sub setup in the back, you could probably get a few pointers from him.
If I ever install a sub it'll be underneath the back left seat, which is where I think my 300w amp that came with the truck is located at. I might want to get another one just for a sub :P
_____________________________
Jimmy Clack
2005 Dakota QC Laramie V8 4x2
K&N 63 | Flowmaster 40 | DeeZee Bull Guard | 6x Hella 500 | CB Radio | Full LED Conversion | HID Headlights / Foglights
|
|
|
|
RE: ZOMGAH!!!!!!! - 6/5/2006 8:57:28 PM
|
|
|
white26golf
Posts: 386
Joined: 3/19/2006
Status: offline
|
OK, so I want to take off my rear headrests like you did. I can get the bottom of the back panel free, but can't seem to get the top off. I also don't want to break anything so I can put the back panel back on. A little help is needed.
_____________________________
|
|
|
|
|
RE: ZOMGAH!!!!!!! - 6/5/2006 10:50:56 PM
|
|
|
maxmax
Posts: 80
Joined: 1/28/2006
Status: offline
|
quote:
ORIGINAL: white26golf
OK, so I want to take off my rear headrests like you did. I can get the bottom of the back panel free, but can't seem to get the top off. I also don't want to break anything so I can put the back panel back on. A little help is needed.
I removed mine. I did not take off the back panel. Shine a light around the top edge of the panel and you will see the plastic push pins. I believe there was four of them, pull these loose. If you damage them you will have to get new ones. I used and open end wench from the top side of the panel to remove the hex head bolts.
_____________________________
05 DAK CC 4X4 SLT 4.7L, 26E pak, 5 speed auto, 17" acc wheel, nerf bar, tinted, front tow hooks, tow receiver, alumium gas cover, spray bed liner, K&N filter,180 stat, Magnaflow muffler, leveling shackles,etc, etc
|
|
|
|
|
RE: ZOMGAH!!!!!!! - 6/7/2006 10:14:12 AM
|
|
|
white26golf
Posts: 386
Joined: 3/19/2006
Status: offline
|
Is there a tool or something u used to get the pins out. I don't just want to pull really hard and break them.
_____________________________
|
|
|
|
|
RE: ZOMGAH!!!!!!! - 6/7/2006 8:47:34 PM
|
|
|
maxmax
Posts: 80
Joined: 1/28/2006
Status: offline
|
I use a long needle nose pliers with a long handle, but there are other tools out there, maybe a long flat bar or the tool the dealer would use for removal. The pins are firmly fasten inplace. good luck
quote:
ORIGINAL: white26golf
Is there a tool or something u used to get the pins out. I don't just want to pull really hard and break them.
_____________________________
05 DAK CC 4X4 SLT 4.7L, 26E pak, 5 speed auto, 17" acc wheel, nerf bar, tinted, front tow hooks, tow receiver, alumium gas cover, spray bed liner, K&N filter,180 stat, Magnaflow muffler, leveling shackles,etc, etc
|
|
|
|
|
RE: ZOMGAH!!!!!!! - 6/7/2006 9:29:58 PM
|
|
|
maxmax
Posts: 80
Joined: 1/28/2006
Status: offline
|
Okay to be correct. I looked up the correct tool the service manual recommends for removal of the back panel. It is a TRIM STICK C-4755
quote:
ORIGINAL: maxmax
I use a long needle nose pliers with a long handle, but there are other tools out there, maybe a long flat bar or the tool the dealer would use for removal. The pins are firmly fasten inplace. good luck
quote:
ORIGINAL: white26golf
Is there a tool or something u used to get the pins out. I don't just want to pull really hard and break them.
_____________________________
05 DAK CC 4X4 SLT 4.7L, 26E pak, 5 speed auto, 17" acc wheel, nerf bar, tinted, front tow hooks, tow receiver, alumium gas cover, spray bed liner, K&N filter,180 stat, Magnaflow muffler, leveling shackles,etc, etc
|
|
|
|
 Today's Posts
Most Active Topics
Make A Donation
Forum Rules & FAQ
RSS Feeds
SRT Forums
Race News
Dodge Prices
Dodge Trucks & SUVs
Ram  Dakota
Durango Nitro
Dodge Cars
Avenger Intrepid
Caliber Magnum
Challenger Neon
Charger Stealth
Daytona Stratus
Dodge Viper
Advertising Info
|
Contact Us |
Link To Us |
Sitemap |
Archive |
Advertising |
Automotive Directory |
About Us |
Dodge Links |
Legal |
Privacy Policy |
© Dodge Forum
Harley Davidson |
Ford Mustang Forums |
Dodge Challenger
Dodge Forum .com is not affiliated with or endorsed by Daimler Chrysler.
|
Printable Version
