Programming key fobs...I can't get it completed!!!

Printable Version

Dodge >> Dodge SUVs >> Dodge Durango >> 2nd Gen Durango >> Programming key fobs...I can't get it completed!!!

Page: [1]

Login Message << Older Topic   Newer Topic >>

Programming key fobs...I can't get it completed!!! - 5/7/2008 8:14:01 PM    jefflawrence7   Posts: 1 Joined: 5/7/2008 Status: offline I recently purchased 2004 Durango ST...At time of purchase I was given 3 key fobs (none of which were working)  one is brand new...In following the instructions to program (simple I thought)  everything works fine until the step where I simply press the unlock bottom to complete programming ( I never receive that last single tone!!!  Does anyone have any tips?  This is the procedure I am following... 1. Enter your vehicle and close all doors. 2. Fasten your seat belt (Fastening the seatbelt will cancel any chiming that may confuse you during this programming procedure). 3. Place the key into the ignition. 4. Turn the ignition to the ON position ( Do not start the engine ). 5. Press and hold the UNLOCK button on the key fob. 6. After holding the UNLOCK button for four seconds, also press the PANIC button within 6 seconds. 7. When a single chime is heard release both buttons. The chime is an indication that you have successfully entered program mode. All fobs that are to be programmed must be done so within 60 seconds of when the chime was heard. 8. Using the fob to be programmed, press and release both the LOCK and UNLOCK buttons, simultaneously. 9. A single chime will be heard. 10. Within four seconds of hearing the chime, press and release the UNLOCK button on the fob. 11. A single chime will be heard. 12. Repeat steps 8 through 10 to program up to six additional fobs. 13. Turn the ignition to the OFF position. 14. Your vehicle will remain in program mode up to 60 seconds from when the original chime was heard. After 60 seconds, all programmed fobs function normally. Post #: 1

RE: Programming key fobs...I can't get it completed!!! - 5/20/2008 5:39:55 PM    wizardny1   Posts: 6 Joined: 12/16/2007 Status: offline To use the procedure in the manual, at least one fob must be working. If none of them are working then you have to take it to the dealer to have it programed. I had the same issue with my 04. I bought it used and none of the fobs worked so the used car dealer ordered a new one for it. Then they had to take it to a dodge dealer to get it to work. Once the new one was programed I was able to get the others to work. (in reply to jefflawrence7) Post #: 2

Today's Posts
Most Active Topics
Make A Donation
Forum Rules & FAQ
RSS Feeds
SRT Forums
Race News

Dodge Prices

Dodge Trucks & SUVs
Ram Dakota
Durango Nitro

Dodge Cars
Avenger Intrepid
Caliber Magnum
Challenger Neon
Charger Stealth
Daytona Stratus
Dodge Viper

Featured Sponsors

Poll
Now that you've seen the 2008 Dodge Challenger SRT-8, what do you think?
	I Love It, Its Perfect
	I love the looks, but hate the transmission
	I like it, but I want the concept interior
	I like it, but I want the exact concept exterior
	Its ok, but the concept was far better
	Thanks, but I look forward to some changes on the 2009 models.
Poll Results Previous Polls

Top 10 Posters
dustyloins 21040 badstratrt 20755 midnight 17495 vipergts 14475 dodgegirl19 13072 ramfan5.9 12435 steve05ram36 11346 nickoman01 10864 drew 10116 casper 9606

New Vendors
Truxedo
Airaid
Mopar Biz
ATI ProCharger
Motor City Auto Parts
Sonic Electronix
Buy Auto Truck Accessories
Buy Car Floor Mats
Edge Products
AMSOIL - Performance Oil Technology